Bakin Karfe Strip & Maganin Yankan Masana'antu

Blog

Gida > Blog

SUS304 vs SUS301 Stainless Steel Strip: Differences, Properties and Applications

Table of Contents

SUS304 vs SUS301 Stainless Steel Strip: Quick Answer

The key difference between SUS304 and SUS301 stainless steel strip is the balance between corrosion resistance/formability and work-hardened strength. SUS304 is the general-purpose 18-8 austenitic grade preferred for chemical equipment, food-contact surfaces, deep drawing, and welded structures. SUS301 is a metastable austenitic grade with higher carbon and lower chromium/nickel; after cold rolling, it can achieve much higher strength, hardness, and elasticity, but its corrosion margin is generally lower and it is less commonly listed for direct food contact.

For chemical equipment manufacturers, food machinery manufacturers, and material buyers, the selection question is not “which grade is better.” It is: does the application prioritize corrosion resistance and formability, or high strength and spring-like elasticity?


At-a-Glance Comparison: SUS304 vs SUS301 Stainless Steel Strip

Comparison PointSUS304 Stainless Steel StripSUS301 Stainless Steel Strip
Grade family18-8 austenitic stainless steel; AISI 304 equivalentMetastable austenitic stainless steel; AISI 301 equivalent
Chemical compositionCr 18.00–20.00%, Ni 8.00–10.50%, C ≤0.08%Cr 16.00–18.00%, Ni 6.00–8.00%, C ≤0.15%
Annealed yield strength≥205 MPa≥205 MPa
Annealed tensile strength≥520 MPa≥515–520 MPa
Maximum cold-rolled strengthLimited compared with SUS301Can exceed 1300–1700 MPa depending on temper
Corrosion resistanceGenerally better in most service environmentsLower margin in many chloride/acid environments
Work-hardening tendencyModerateVery high
FormabilityExcellent for deep drawing and complex formingGood in annealed condition; limited in hard tempers
Typical roleCorrosion-resistant, formable, weldable stripHigh-strength, spring-grade, fatigue-resistant strip
Food-contact complianceWidely listed in major food-contact frameworksLess commonly listed for direct food contact
Best fitChemical equipment, food machinery contact parts, tanks, pipes, deep-drawn partsSprings, clips, connectors, precision structural parts, elastic components

1. Basic Positioning of SUS304 and SUS301

SUS304 is a JIS-designated 18-8 chromium-nickel austenitic stainless steel, corresponding to AISI 304. Its composition is designed for a balanced combination ofcorrosion resistance, formability, weldability, and cleanliness. In the annealed condition, it has a single austenitic structure and moderate work-hardening behavior, making it suitable for deep drawing, complex stretching, and welded assemblies. SUS304 stainless steel strip is widely used in food processing equipment, chemical apparatus, heat exchangers, tanks, piping, and general corrosion-resistant structures.

SUS301 is ametastable austenitic stainless steel corresponding to AISI 301. It contains more carbon and less chromium and nickel than SUS304. This composition allows rapid work hardening during cold rolling, accompanied by strain-induced martensite formation. As a result, SUS301 stainless steel strip can achieve very high strength and hardness in cold-rolled tempers. It is not a general-purpose corrosion-resistant grade; it is afunctional grade selected for strength, elasticity, fatigue resistance, and precision structural performance, commonly used in springs, spring contacts, clips, connectors, and high-strength precision parts.


2. Chemical Composition and Mechanical Property Differences

2.1 Haɗin Sinadari: Carbon Up, Chromium and Nickel Down

The composition difference can be summarized simply: SUS301 trades some corrosion resistance for much greater work-hardening potential.

Abun cikiSUS304SUS301
C≤0.08%≤0.15%
Cr18.00–20.00%16.00–18.00%
Ni8.00–10.50%6.00–8.00%
Mn≤2.00%≤2.00%

The higher carbon content of SUS301 is the metallurgical basis for its high strength after cold rolling. However, higher carbon also increases the risk of carbide precipitation during welding and reduces corrosion safety margin. SUS304’s lower carbon and higher chromium/nickel content provide a wider safety margin for corrosion resistance and welding.

2.2 Annealed Mechanical Properties: Similar Lower Limits, Different Practical Performance

In the annealed condition, the specified lower limits for yield strength and tensile strength appear similar. The real difference appears after cold rolling.

PropertySUS304 AnnealedSUS301 Annealed
Yield strength≥205 MPa≥205 MPa
Tensile strength≥520 MPa≥515–520 MPa
Elongation≥40%≥40%
TauriApproximately ≤90 HRBApproximately ≤95 HRB

These annealed values can create the false impression that the two grades perform similarly. In practice, SUS301 work-hardens much faster. At the same cold-reduction ratio, SUS301 gains strength and hardness far more rapidly than SUS304. SUS301 can reach tensile strengths above1300 MPa, with special EH and ultra-high-strength tempers exceeding1570 MPa and, in some cases, 1700 MPa. SUS304 cold-rolled strip generally cannot reach this strength level in standard tempers.


3. Corrosion Resistance Comparison

SUS304 generally offers better corrosion resistance than SUS301 in most service environments. This is primarily due to its higher chromium content and lower carbon content. Chromium is the key element for forming and stabilizing the passive film on stainless steel. SUS304 contains 18–20% Cr, while SUS301 contains 16–18% Cr. SUS301’s higher carbon content also increases the risk of grain-boundary carbide precipitation, further reducing its corrosion safety margin.

However, corrosion behavior is environment-specific. One immersion study in boiling NaCl solution reported that SUS304 showed more severe pitting than SUS301 under those specific conditions, with average weight loss reaching up to 30% after 1500 hours for SUS304 versus 16% for SUS301. This result must be interpreted in context: in aboiling, high-concentration chloride environment, SUS301 performed better than SUS304 in that particular test. It does not mean SUS301 is more corrosion-resistant in all chloride environments.

Inambient neutral salt spray, mild acids, food media, and general chemical atmospheres, SUS304 remains the more reliable corrosion-resistant choice because of its higher chromium content and more stable passive film. For practical selection, do not rely on a single corrosion test result. Evaluate the actual medium, temperature, chloride concentration, surface finish, and cleaning regime. For acidic chemical media, chloride-containing process water, or aggressive cleaning agents, SUS304 usually has a wider corrosion margin. For extreme chloride conditions beyond the capability of both grades, consider molybdenum-bearing 316L or duplex stainless steel rather than substituting SUS301 for SUS304.


4. Tauri, Strength, and Processing Performance

4.1 Work Hardening: SUS301’s Core Advantage

SUS301 work-hardens much faster than SUS304. During cold rolling, its austenitic structure undergoes strain-induced martensite transformation, causing hardness and strength to rise sharply while elongation drops rapidly. This allows SUS301 to provide a continuous hardness range from soft annealed strip to ultra-hard temperfrom the same chemistry, whereas SUS304 has a much narrower hardness adjustment window.

Typical mechanical properties of common SUS301 tempers are shown below:

TemperTensile Strength, min.Vickers Hardness, min.Approx. Elongation
ANN520 MPa≤218 HV40%
1/2H930 MPa310 HV10%
3/4H1130 MPa370 HV5%
H1320 MPa430 HV—
EH1570 MPa490 HV—

By comparison, SUS304 cold-rolled strip increases in hardness more moderately. Common hard-temper starting points for SUS304 are often around HV≥250, then HV≥310 and HV≥370, but the overall hardness and strength ceiling is lower than that of SUS301 EH. SUS301’shigh yield strength, elastic limit, and fatigue resistance in hard tempers make it a preferred material for springs, spring contacts, and precision elastic components.

4.2 Formability: SUS304’s Home Ground

If the application requiresdeep drawing, complex stretching, or large plastic deformation, SUS304 is usually the more rational choice. Its moderate work-hardening tendency and high ductility allow significant cold forming without cracking. SUS301 in the annealed condition also has some forming capability, but once hardened, elongation drops sharply and complex bending or deep drawing becomes difficult.

A common selection mistake is to choose SUS301 full-hard solely for strength and then experience cracking during forming. The correct logic is:

  1. Determine the maximum allowable hardness based on the forming operation.
  2. Select the softest temper that still meets the final strength requirement.
  3. Where possible, use SUS301半-hard condition and allow the forming process itself to provide additional work hardening.

5. Material Selection for Chemical Equipment and Food Machinery

5.1 Kayayyakin Sinadarai: SUS304 Is the Corrosion-Resistance Baseline; SUS301 Handles High-Strength Non-Wetted Structures

In chemical equipment, long-term corrosion reliability takes priority over short-term strength. SUS304 has a mature engineering track record in atmospheric exposure, fresh water, many acidic and alkaline media, and general chemical service. It is a baseline strip material for tanks, heat exchangers, piping, reactor internals, and general chemical structures.

SUS301’s appropriate role in chemical equipment ishigh-strength, non-wetted structural and elastic components, such as spring supports, clips, screens, and high-load connectors. When the medium contains high chloride levels or has a significant pitting risk, SUS304 itself may lack sufficient corrosion margin. In that case, the correct upgrade path is 316L or another molybdenum-bearing grade, not SUS301.

5.2 Food Machinery: Compliance Is a Structural Barrier for SUS304

Food-contact applications require not only corrosion resistance but alsoregulatory compliance. SUS304 is widely listed in major food-contact material frameworks, including U.S. FDA 21 CFR, EU (EC) No 1935/2004, NSF/ANSI 51, and China’s GB 4806 series. It is a common austenitic grade for food equipment tanks, piping, work surfaces, conveyors, and contact surfaces. With 2B or BA finishes, SUS304 can provide a smooth, non-porous, easy-to-clean hygienic surface.

SUS301 has clear limitations for direct food contact. Major food-contact regulations less commonly list SUS301 explicitly as a direct-contact material. Although its chemistry remains within normal stainless steel limits, its lower chromium content and higher carbon content result in lower long-term corrosion stability than SUS304. Therefore, SUS301 is less frequently used for direct food-contact parts.

In food machinery, the appropriate use of SUS301 is fornon-food-contact structural components—machine frames, housings, supports, springs, clips, and moving parts that require high strength, wear resistance, or elasticity. Structural isolation must ensure that SUS301 does not contact food directly. For direct food-contact strip, select SUS304 or 316L that complies with GB 4806.9-2016, FDA requirements, or the applicable market regulation, and request compliance documentation from the supplier.


6. How to Choose the Right Stainless Steel Strip Grade

Use the following decision framework for project reviews and procurement specifications.

Step 1: Is the part in direct food contact?

If yes, exclude SUS301 from the contact surface and select SUS304 or a higher compliance grade. If SUS301 is used only for non-contact structural parts, proceed to Step 2.

Step 2: Is the corrosion environment beyond SUS304’s comfort zone?

For neutral ambient media, mild acids, fresh water, and general food or chemical cleaning agents, SUS304 is a reasonable baseline. For higher chloride levels, stronger acids, or higher temperatures, evaluate 316L rather than replacing SUS304 with SUS301 to reduce cost.

Step 3: Is the core requirement “corrosion resistance + formability” or “strength + elasticity”?

ChooseSUS304 for deep drawing, complex stretching, welded structures, or a wider corrosion margin.
ChooseSUS301 for high yield strength, high elastic limit, fatigue resistance, spring function, or lightweight high-strength structures.

Step 4: If SUS301 is selected, define the temper based on the forming process.

  • Large forming deformation or subsequent bending: start from ANN or 1/2H and use forming-induced work hardening to reach final strength.
  • Elastic function with simple forming: 3/4H or H.
  • High-stress, high-fatigue-life precision springs or contacts with controllable forming: H or EH.

The core principle is: choose the lowest temper that meets the strength target while preserving forming safety.

Step 5: Specify surface finish.

For food contact and chemical corrosion resistance, prefer 2B or BA surfaces to avoid rough surfaces that can initiate corrosion or trap residue. For SUS301 structural parts, surface requirements may focus more on wear resistance and appearance consistency, but defects that affect fatigue life should still be controlled.


Frequently Asked Questions

Can SUS301 directly replace SUS304 for food-contact surfaces?

No, not recommended. SUS301 is less commonly listed in major food-contact regulations for direct contact, and its long-term corrosion stability is lower than SUS304. SUS301 can be used for non-contact structural parts, springs, and housings in food machinery, but direct food-contact strip should use SUS304 or 316L compliant with GB 4806, FDA, or the applicable regulation.

Is SUS301 always less corrosion-resistant than SUS304?

In most routine service environments, SUS304 offers better corrosion resistance because of its higher chromium and lower carbon content. However, under specific extreme conditions such as boiling high-concentration NaCl, one study observed lower weight loss for SUS301 than SUS304. Selection should not rely on a single data point; evaluate the actual medium, temperature, chloride concentration, and surface condition.

How strong can SUS301 stainless steel strip become?

Through cold rolling and work hardening, SUS301 can reach tensile strengths above 1300 MPa. EH temper can exceed 1570 MPa, and special processes can exceed 1700 MPa. SUS304 cold-rolled strip generally cannot reach this strength level in standard tempers.

How should buyers interpret the price difference between SUS304 and SUS301?

At the base grade level, SUS301 is sometimes quoted slightly lower than SUS304. However, because SUS301 requires more controlled hardening and precision slitting, the finished strip price may be higher than SUS304. Procurement decisions should consider compliance cost, forming yield, and lifecycle reliability—not only price per ton.

If SUS304 corrosion resistance is insufficient, should I switch to SUS301 or 316L?

Choose 316L. The 2–3% molybdenum addition in 316L significantly improves resistance to chlorides, acids, and saltwater. SUS301 is designed for strength and elasticity, not as a corrosion-resistance upgrade from SUS304.

Ask About Hardness Options

a tuntuɓi